Skip to main content

Search

Unpowered Asset Gateway (AG) Installations

a31548 a722e2

Unpowered Asset Gateways, such as the AG45, AG46, and AG51, are wallet-sized trackers ideal for monitoring assets like intermodal containers, construction equipment, dumpsters, light towers, and other mobile assets. The AG features customizable GPS check-ins, a replaceable lithium battery that lasts between 1-5 years depending on the model, and a waterproof and ruggedized enclosure. The AG enables increased asset utilization, theft recovery, and optimized pool inventory management.

AG46.png
AG51.png

Install an Unpowered Asset Gateway

Before you begin activation and installation, ensure that the device is within a geographical area with cellular coverage.

Perform the setup and installation instructions for your unpowered AG model:

Set up and Install the AG51

To install an AG51 Unpowered AG, perform the following workflow:

  1. Activate the device in the Samsara dashboard if you have not already done so.

  2. To initiate a test ping, press and hold the button on the AG faceplate until the LED illuminates green, for no more than 2-3 seconds.

    The LED flashes green every 3 seconds for up to 5 minutes while the device attempts to check in with the Samsara dashboard. After the device determines status, the LED displays a color LED for 5 seconds to indicate the connection status. To surface the most recent check-in information to the Samsara dashboard, double-press the setup button.

    AG51setupbutton.png

    Warning

    If you press the setup button for more than 4 seconds, the device will reboot. If the device reboots, wait five minutes before you restart the test ping in this step.

  3. Perform the action that corresponds to the observed solid LED behavior:

    AG LED Status and Actions

    green_safety_dot.png Solid green LED

    Status: Successful connection: Cellular connection OK, GPS OK

    Action

    Confirm the device is active in the Samsara dashboard (Overview > Assets > Unpowered).

    Device registration can take up to 30 minutes to complete.

    red_safety_dot.png Solid red LED

    Status: Unsuccessful connection: Cellular connection fail, GPS fail

    Action

    1. Ensure that the device is outside and avoid obstructions such as underground structures, heavily insulated buildings, bridges, and trees.

    2. Ensure that the device has a clear view of the sky and is within cellular range.

    3. Press and hold the button for 1-2 seconds and perform the action that corresponds to the observed LED behavior.

    blue_LED_dot.png Solid blue LED

    Status: Partial connection: Cellular connection OK, GPS fail

    Action

    1. Ensure that the device is outside and avoid obstructions such as underground structures, heavily insulated buildings, bridges, and trees.

    2. Press and hold the button for 1-2 seconds and perform the action that corresponds to the observed LED behavior.

    yellow_dot.png Solid yellow LED

    Status: Partial connection: Cellular connection fail, GPS OK

    Action

    1. Ensure that the device has a clear view of the sky and is within cellular range.

    2. Press and hold the button for 1-2 seconds and perform the action that corresponds to the observed LED behavior.

  4. Prepare the install surface with the provided alcohol wipe, then select a suitable install location.

    Tip

    When selecting a location for your device, reference the following tips:

    • Ensure that the AG has a clear view of the sky.

    • Avoid installing the device within metallic structures, such as within metal trailers. Placement in such structures may adversely impact device cellular and GPS connectivity.

    • Position the AG vertically. Avoid mounting it with the back facing directly upward or downward, such as lying flat on its back or front.

  5. Attach the mounting bracket to the mounting surface using one of the following methods:

    Caution

    To prevent damage to the mounting tabs, tighten screws to a maximum torque of 1.4 Nm (12.4 lbf-in). If using your own screws, ensure they are not larger than the size specified below.

    bracket.jpg

    • Self-drilling screws: Use the provided #8 self-drilling screws.

      drillscrewsize.jpg

    • Machine screws: Drill through-holes for the mounting bracket and secure it using the provided 6-32 machine screws, washers, and lock nuts.

      machinescrewandbolt.jpg

  6. Securely mount the AG to the bracket using the two provided machine screws.

    Caution

    To prevent damage to the mounting tabs, tighten screws to a maximum torque of 1.4 Nm (12.4 lbf-in). If using your own screws, ensure they are not larger than the size specified below.

    AG51Install.jpg
    machinescrewsize.jpg

  7. (Optional) Camouflage the AG, as needed.

    If you use spray paint, choose a non-metallic paint that will not interfere with antenna performance.

  8. (Optional) Configure the check-in schedule for the AG.

    By default, the AG check-in frequency is every 12 hours.

    Using the default check-in settings and assuming normal cellular connectivity and normal environmental conditions, the batteries will operate for 3-5 years.

Set up and Install the AG45/AG46

To install an unpowered Asset Gateway (AG), follow the detailed workflow below or review the PDF install guide AG45/AG46 Install Guide (PDF)

To install an AG45 or AG46 Unpowered AG you will need:

image51.png

  1. Activate the device in the Samsara dashboard if you have not already done so.

  2. Remove the protective sticker from the side of the AG.

  3. Use the provided pin to press and hold the button until the light turns green (1-5 seconds) and then release the pin.

    presspinAG46.png

    The LED stays green for 5 seconds to indicate the device is active.

  4. Confirm the device is active in the Samsara dashboard (Overview > Assets > Unpowered).

    Device registration can take up to 30 minutes to complete.

  5. Prepare the install surface with the provided alcohol wipe, then select a suitable install location.

    Tip

    When selecting a location for your device, reference the following tips:

    • Ensure that the AG has a clear view of the sky.

    • Avoid installing the device within metallic structures, such as within metal trailers. Placement in such structures may adversely impact device cellular and GPS connectivity.

    • Position the AG vertically. Avoid mounting it with the back facing directly upward or downward, such as lying flat on its back or front.

  6. Mount the AG on the asset using one of the following methods:

    With screws:

    1. Position the AG on the mounting location.

    2. Mark the location for the screws.

    3. Remove the AG and drill small pilot holes in the screw locations.

    4. Attach the gateway to the asset using the provided screws and tighten screws with the anti-theft bit key.

    Without screws:

    1. Place the provided VHB adhesive tape on the back of the AG.

    2. Press the AG firmly into place.

  7. (Optional) Camouflage the AG, as needed.

    If you use spray paint, choose a non-metallic paint that will not interfere with antenna performance.

  8. (Optional) Configure the check-in schedule for the AG.

    By default, the AG check-in frequency is every 12 hours.

    Using the default check-in settings and assuming normal cellular connectivity and normal environmental conditions, the batteries will operate for 1-3 years (AG46) or up to 5 years (AG45).

Comments

0 comments

Please sign in to leave a comment.

Powered by Zendesk